Hi,
updated my megadrum32 atmega1024 to latest Firmware. rebooted megadrum, set alternate Encoders to true and my Inputs to 22 like before... then i tried to load my to Slot1 saved Settings and f... seems like megadrum go crazy.... many Inputs are triggering, all Settings are set to really crazy results... ex: latency 136 note off 500 and so on...
all my Settings are gone... whats that? remember, had it the first time, the update before this one...
Strange Behavior after Update
Moderator: Related software moderators
4 posts
• Page 1 of 1
Strange Behavior after Update
by talrusher » Wed Sep 04, 2013 5:36 pm
Here I stand in the falling rain
There is no joy inside these tears
I see the world through a twisted and bitter stare
To be where I have been... to see what I have seen
Is it a dream?
Or can I believe...
The memories will haunt me for evermore
There is no joy inside these tears
I see the world through a twisted and bitter stare
To be where I have been... to see what I have seen
Is it a dream?
Or can I believe...
The memories will haunt me for evermore
- talrusher
- Posts: 111
- Joined: Sun Nov 27, 2011 2:27 pm
- Location: Germany
Re: Strange Behavior after Update
by angr77 » Wed Sep 04, 2013 7:30 pm
Sounds strange - Firmware version?
Talrusher - You are skilled...but dare I ask you if you did a backup in MDM of all the MD settings first, before upgrading. A firmware upgrade wipes everything in the MD. (To my knowledge)
I am using a ARM based MegaDRUM-32 with 2013-06-12 firmware. I have not had the chance to upgrade to 2013-09-01 yet.
Angr77
Talrusher - You are skilled...but dare I ask you if you did a backup in MDM of all the MD settings first, before upgrading. A firmware upgrade wipes everything in the MD. (To my knowledge)
I am using a ARM based MegaDRUM-32 with 2013-06-12 firmware. I have not had the chance to upgrade to 2013-09-01 yet.
Angr77
Sonor, Drum-Tec heads, Roland CY14, CY12&15R, 2x BT-1 & VH11, 12, 13, Triggera D11, 2xD14, Pintech Dingbat, Letric Moo, Quartz triggers, 2xARM based MegaDRUM, PS Board, M-Audio FT Ultra 8R, Addictive Drums 2.1.6, Surface Pro 5 http://zourman.com
- angr77
- Posts: 622
- Joined: Tue Nov 29, 2011 10:42 pm
- Location: Stockholm, Sweden
Re: Strange Behavior after Update
by dmitri » Wed Sep 04, 2013 8:07 pm
You shouldn't load settings in a newer firmware version saved with an older firmware version in EEPROM - unexpected behavior is very likely. Use MDM to save settings between upgrades.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
Re: Strange Behavior after Update
by talrusher » Wed Sep 04, 2013 11:22 pm
...sh** ... ^^
have allway made updates without saving anything... and allways it goes right. okay. for future updates i would remember your words.
thx
bye ;D
have allway made updates without saving anything... and allways it goes right. okay. for future updates i would remember your words.
thx
bye ;D
Here I stand in the falling rain
There is no joy inside these tears
I see the world through a twisted and bitter stare
To be where I have been... to see what I have seen
Is it a dream?
Or can I believe...
The memories will haunt me for evermore
There is no joy inside these tears
I see the world through a twisted and bitter stare
To be where I have been... to see what I have seen
Is it a dream?
Or can I believe...
The memories will haunt me for evermore
- talrusher
- Posts: 111
- Joined: Sun Nov 27, 2011 2:27 pm
- Location: Germany
4 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 181 guests